Connect with H&H

DIY Roman Shade

DIY Roman Shade - House & Home

A perfect way to add pattern and privacy to your space.

Materials and Tools

  • Drapery fabric
  • Cotton, dim out or black out for drapery lining
  • Mounting board 1”x1” cut to the inside width of the window
  • 1-1/2” #8 screws for mounting to window
  • Velcro
  • Drapery cord — for each row of rings to raise and lower the shade
  • 1/2” plastic drapery rings
  • I-beam drapery track, wood dowel or 3" wood board to weight shade
  • Staple gun and staples
  • Screw eyes
  • Cord cleat for anchoring the cord when the blind is up

Step 1

After deciding on where the shade will be mounted — roman shades can be mounted inside or above the window frame — measure width and length of window. Cut drapery fabric 2” wider and 24” longer than the measurement of the window.

Step 2

Cut a piece of lining fabric 1" smaller than width of drapery fabric and 8” shorter. 

Step 3

Pin lining and drapery fabric with outside-facing sides turned inside, with tops even and lining fabric 8” shorter at the bottom. Sew the lining flush to the edge of the drapery fabric with 1” seam allowance, leaving the top and bottom open.

Step 4

Turn shade right side out and press seams flat (the lining will be slightly inset from the overall piece).

Step 5

To hem, fold 4” of drapery fabric at bottom of shade up, then fold up again another 4” (this is the excess overhanging the lining fabric). Press and sew into place.

Step 6

Sew soft side of the Velcro strip to the top of the shade on the drapery fabric side. Adding decorative piping along the top is also an option before sewing on the Velcro at this stage. If adding piping, sew a strip the width of the shade near the top of the shade, just below where the lower edge of the Velcro strip will fall.

Step 7

Determine ring placement locations: using a large metal set square and a pencil, mark for the first row of rings 1” in from each shade edge, and every 6” to 8” across the width of the shade. Mark the next row 8” above the first, until all rows are marked. You may have to play with placement a little depending on the exact length and width of your shade.

Step 8

Insert metal screw eyes into 1” x 1” wood mounting strip to line up with the top of each vertical row of rings.

Step 9

Sew rings on shade by hand or using a sewing machine (make sure to go through both the liner and fabric).

Step 10

Drill holes for screws in other side of 1” x 1” wood mounting strip.

Step 11

Staple hook side of Velcro to mounting strip. Attach shade to mounting strip with Velcro.

Step 12

Cut one length of drapery cord for each row of rings. Each cord should go up through the rings in each vertical row on the shade, across the top through each screw eye on the mounting strip and dangle down one side for raising and lowering the shade. Cut each length of drapery cord row by row, as each length will be different.

Step 13

Knot drapery cords on rings in bottom row on shade.

Step 14

Slide I-beam drapery track, board or wood dowel into bottom hem and sew hem closed.

Step 15

Mount shade to window frame using 1-1/2” #8 screws with the velcro sandwiched in between the frame and mounting board. Raise shade to bottom of window; adjust cords and tie in knot at screw eye on mounting strip. This prevents the shade from hanging unevenly when lowered. Braid cords to tidy ends.

Step 16

Install cord cleat on window frame at a convenient height. Secure cords to cleat when shade is at desired position on window.

See the pretty floral roman shade assistant design editor Lauren Petroff made for her own kitchen using these instructions.

Author: 

Cameron MacNeil

Photographer: 

Angus Fergusson

Comment Guidelines

We welcome your feedback on Houseandhome.com. H&H reserves the right to remove any unsuitable personal remarks made about the bloggers, hosts, homeowners and/or guests we feature. Please keep your comments focused on decorating, design, cooking and other lifestyle topics. Adopt a tone you would be willing to use in person and do not make slanderous remarks or use denigrating language. If you see a comment that you believe violates any of the guidelines outlined above, please click “Alert a Moderator.” Thank you.

OK